Best printed circuit board assembly provider? Most of our engineer and operators has more than ten years of experience in PCB industry, so we can produce special such as 20 OZ heavy copper board, 4 layers MCPCB, etc. At the same time, we purchased many advanced, art-of-state machines & devices for PCB manufacturing, checking, to improve the quality of our boards. Read extra info at pcb assembly service. The white silkscreen layer is applied on top of the soldermask layer. The silkscreen adds letters, numbers, and symbols to the PCB that allow for easier assembly and indicators for humans to better understand the board. We often use silkscreen labels to indicate what the function of each pin or LED. Silkscreen is most commonly white but any ink color can be used. Black, gray, red, and even yellow silkscreen colors are widely available; it is, however, uncommon to see more than one color on a single board.
Double sided flex circuits consists with double sided copper conductors and can be connected from both sides. It allows more complicated circuit designs, more components assembled. The major material used are copper foil, polyimide and coverlay. Adhesiveless stack up is popular for better dimensional stability, high temperature, thinner thickness. Dual access flexible circuit board refer to the flex circuit which can be accessed from both top and bottom side but only has only layer of conductor trace. Copper thickness 1OZ and coverlay 1mil, it similar with 1 layer FPC and opposite side FFC. There’re coverlay openings on both sides of flex circuit so that there’re solderable PAD on both top and bottom sides, that is similar with double sided FPC, but dual access flex circuit board has different stack up because of only one copper trace, so no plating process is need to make plated through hole (PTH) to connect between top and bottom side, and trace layout is much more simple. Currently our mouthy capability is 260,000 square feet (28,900 square meter), more than 1,000 different boards will be completed. We also provide expediate service, so that urgent boards can be shipped out within 24 hours.
Tg means Glass Transition Temperature. As flammability of printed circuit board (PCB) is V-0 (UL 94-V0), so if the temperature exceeds designated Tg value, the board will changed from glassy state to rubbery state and then the function of PCB will be affected. If working temperature of your product is higher than normal (130-140C), then have to use High Tg PCB material which is > 170C. and popular PCB high value are 170C, 175C, and 180C. Normally the FR4 circuit board Tg value should be at least 10-20C higher than working temperature of product. If you 130TG board, working temperature will be lower than 110C; if use 170 high TG board, then maximum working temperature should be lower than 150C.
Despite all the precautions, damage to the Flexible PCB can occur. That is why one should constantly check for faulty components by testing all components to figure out the faulty ones and then replacing them so that the board functions well. Every so often, the issue could be caused by bad soldering. In such cases checking the soldering condition and repairing it works well. While components and soldering failure are easier issues to tackle, you could also be dealing with a complex circuit issue. If the circuit is indeed the problem, the PCB must be returned to the factory for the necessary repair. These are the most probable factors that may have caused your flexible PCB some damage. When you take care of such factors beforehand, you can avoid damages to your PCBs and save time and effort for your organization. To develop sturdy and long-lasting PCBs, it is always recommended to choose a reputed PCB Fabrication company that develops sturdy PCBs for you that have rare chances of getting damaged.
According to different manufacturing method, current there’re three basic types for ceramic board: A) Thick Film Ceramic Board Thick Film Ceramic PCB: Using this technology, the thickness of conductor layer exceeds 10 micron, more thick than spurting technology. The conductor is silver or gold palladium, and was printed on ceramic substrate. More for Thick Film Ceramic PCB. B) DCB Ceramic Board DCB (Direct Copper Bonded) technology denotes a special process in which the copper foil and the core (Al2O3 or ALN), on one or both sides, are directly bonded under appropriate high temperature and pressure. Discover more details at https://www.bstpcb.com/.
Sometimes people will use abbreviation “MCPCB”, instead of the full name as Metal Core PCB, or Metal Core Printed Circuit Board. And also used different word refers the core/base, so you will also see different name of Metal Core PCB, such as Metal PCB, Metal Base PCB, Metal Backed PCB, Metal Clad PCB and Metal Core Board and so on. MCPCBs are used instead of traditional FR4 or CEM3 PCBs because of the ability to efficiently dissipate heat away from the components. This is achieved by using a Thermally Conductive Dielectric Layer.