Led flood lights manufacturer in China: LED: Semiconductors on a PCB or Board – The light-emitting part inside an LED roadway light is a semiconductor material. Silicon is an abundant material that manufacturers use to produce LED (Light Emitting Diode). There are various ways to manufacture an LED. Here are their descriptions: Wire Bond COB – Wire bonding connects an Individual LED or semiconductor to the substrate. Wire bond LED technology is simple to manufacture, as the integrated circuit is prepared to bond directly to the substrate. Multiple small LEDs are connected to the substrate or PCB, which are then covered by epoxy to seal and protect the electronic circuitry. See extra info at street light factory.
Buyers must thoroughly consider the LED roadway light case design before purchasing. An intelligent design can prevent various failure scenarios, such as water entrapment, grounding, and heating. The material used as LED roadway light casing should be consecutive to dissipate heat and have holes to allow water to drain in case water finds its way into the circuit boxes. Grounding is also necessary to avoid electric shock and can be required by any local regulating body.
The Ingress Protection (IP) is a set of international ratings that tells how much an electrical device is dust and water-resistant. For example, an IP65 rating means the device is dust-resistant and can protect itself against water splashes. The IK ratings are a set of international standards that define the degree of protection for an electrical enclosure against external mechanical impacts. The numeric representation of the IP/IK rating is from 0-10. A higher IK08 rating means the electrical flood light can withstand physical shocks. Having a solid IP/IK rating is vital for installation in a public place. Manufacturers refer to a flood light’s lifespan in terms of working hours (h). Working hours depend on multiple factors, including the type of lamp and the weather conditions in which it is installed. LED-type floodlights offer the most working hours, up to 50,000 hours.
Office Lighting is a high-grade indoor lighting fixture. Its outer frame is anodized by aluminum alloy. The light source is LED. The whole lamp design is simple and elegant, and the atmosphere is luxurious. It has good lighting effect and can bring people the feeling of beauty. The LED flat panel light is unique in design, and the light passes through the high light transmittance light guide plate to form a uniform planar light-emitting effect, and the illumination uniformity is good, the light is soft, comfortable and bright, and the eye fatigue can be effectively alleviated. LED panel lamp can also prevent radiation and will not irritate the skin of pregnant women, the elderly and children. Suitable for hotels, bars, western restaurants, cafes, home interiors, and other indoor lighting, it can directly replace the original ordinary fluorescent lamps, and its brightness is higher. Applicable occasions: Suit for Office, school, hospital, conference room, hotel,shopping malls, clothing stores and museums, galleries, cultural centers and other places.
CHZ Lighting is the leading LED street light manufacturer in China, offering professional LED lighting fixture solutions for muliti applications and environments. Our main products include road lighting, garden lighting, solar lighting, LED flood light, stadium lighting, industrial plant lighting, warehouse lighting, etc. CHZ is a professional LED street light manufacturer, LED flood light factory and lighting solution provider for over 12 years. We adhere to the high standards of “Technological Innovation, Consistent Quality”, continuously developing new products.
Flood lighting, also known as the LED spotlight and LED projection light, is controlled by built-in microchips. There are two types of chips, one is the combined power chip and the other is a single high-power chip. The former has a more stable performance, but the later has a large structure and can achieve very high power to offer long-distance and large-area illumination. LED flood light illuminates the surface higher than the surrounding. It is also known as the spotlight. Typically, the best LED flood light can be aimed in any direction and its structure is seldom affected by climates.
Applicable occasions: roads, streets, and factories, parking lots, rural, mountainous and remote areas, yards, schools, squares and other outdoor environments. It helps boost domestic traditional lighting to green new energy LED lighting. Certificates: CE, RoHS, ISO9000, ISO14000. CHZ Lighting, as the leading solar street light manufacturer and factory, is able to provide top lighting soluton service for your projects, all in one solar street light wholesale, just contact us now! Find even more info on chz-lighting.com.
The module LED street light source area is large, the light is uniform, and the illumination range is wide. Modular LED street lights can flexibly design the number of modules according to requirements, reasonably allocate the number and spacing of modules, and have a larger dispersion surface. Therefore, the light source area is relatively large and the light output is uniform. Module LED street light has good stability Module led street lights can be configured with high-quality driving power according to requirements, which will make the brightness, quality and stability of the entire lamp better.
Waterproof problems in the installation of LED street lights: After ensuring the quality of the lamp holder, you need to pay attention to the technical problems of the lamp holder installation and construction. Most of the led street light controllers are installed in the lampshade and battery box, and generally will not enter water, but in actual engineering cases, some are due to improper installation or The circuit board of the controller is not treated with three-proof paint, which will cause a short circuit due to rain water flowing into the led street light controller along the external wiring of the controller terminal. Therefore, during construction, attention should be paid to bending the internal connecting wires of the controller terminals into a “U” shape and fixing them, and the connecting wires exposed to the outside are also fixed to a “U” shape, so that rainwater cannot enter and cause the controller to short circuit. You can also apply waterproof glue on the inner and outer line interfaces to waterproof.
After the lighting renovation of these venues is completed, the lighting effect has been greatly improved, and it has also been highly praised by the teachers and students of the whole school. Next, the CHZ-LIGHTING team will carry out the lighting renovation work of other venues. In the field of sports lighting,CHZ-LIGHTING has accumulated rich experience in stadium lighting projects with the help of high-quality lighting products and professional service capabilities, and has created many classic project cases all over the country. In the future,CHZ-LIGHTING will continue to cultivate with a more professional attitude, constantly temper its own innovation core, and bring a new lighting experience to more stadiums and sports events by creating professional sports lighting lighting design.